Step Plumbing Guide for Installing a Bathtub
Step Plumbing Guide for Installing a Bathtub
Blog Article
This great article in the next paragraphs pertaining to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround is immensely stimulating. Read it for your own benefit and see what you think of it.
Setting up a bath tub isn't specifically brain surgery, but it does require strong plumbing, carpentry, as well as often, tiling skills. Replacing an old tub with a brand-new one is additionally a reasonably hard project. If the old tub is easily obtainable, the project can move immediately; if you have to open a wall surface to remove the old tub and position the brand-new bathtub, the job is a lot harder. In either case, the project is within a home handyman's abilities, although you will certainly need an assistant to vacate the old bathtub and set in the new one. See to it you have certified on your own for the task as well as fit attempting it. As opposed to hiring a service provider to take over a halfway-completed project, it is better to think about utilizing one before you begin. Opportunities are you might need a professional plumber to make tube links.
This short article will aid you set up a new tub in your washroom if you have already acquired a brand-new tub as well as don't need to alter the arrangement of your previous water system pipes.
Your tools as well as material checklist ought to consist of the following:
Removing Old Taps
If you need to change old taps with brand-new ones as a part of your installment, after that the first thing you need to do is disconnect the water system. After doing so, switch on the faucets to drain pipes any type of water remaining in the system. The process of eliminating the existing faucets can be quite bothersome as a result of the limited access that is often the case.
Utilize a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that connects the supply pipelines to the faucets. Have a cloth all set for the remaining water that will certainly come from the pipelines. When the supply pipes have actually been removed, use the same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly require to stop the solitary taps from turning during this process. Once the taps have been gotten rid of, the holes in the bath/basin will have to be cleaned of any kind of old sealing substance.
Prior to proceeding to fit the brand-new faucets, contrast the pipe connections on the old faucets to the brand-new taps. If the old faucets are longer than the new faucets, after that a shank adapter is required for the new taps to fit.
Fitting New Touches
If the tails of the new faucets are plastic, then you will require a plastic adapter to prevent damage to the thread. One end of the connector fits on the plastic tail of the tap as well as the other end offers a link to the existing supply pipes.
If you need to fit a monobloc, after that you will certainly call for lowering couplers, which attaches the 10mm pipeline of the monobloc to the conventional 15mm supply pipeline.
Next off, position the tap in the installing hole in the bath/basin making certain that the washers remain in location between the faucet and also the sink. Protect the faucet in position with the maker supplied backnut. Once the faucet is securely in position, the supply pipelines can be linked to the tails of the faucets. The faucets can either be connected by using corrugated copper piping or with normal faucet adapters. The previous kind should be linked to the faucet ends initially, tightening only by hand. The supply pipes can later be linked to the various other end. Tighten both ends with a spanner after both ends have actually been linked.
Setting up the Bathtub
Making use of the two wooden boards under its feet, position the bathtub in the called for setting. The wood boards are helpful in evenly spreading out the weight of the bathtub over the area of the boards instead of concentrating all the weight onto four small points.
The following objective is to make sure that the bath tub is leveled all round. This can be accomplished by checking the level as well as adjusting the feet on the bathtub till the spirit level reviews level.
To mount taps, fit all-time low of the furthest versatile tap port to the ideal supply pipeline by making a compression join; after that do the same for the other tap.
Switch on the water supply and also examine all joints and also brand-new pipework for leaks and also tighten them if essential. Fill the bathtub and likewise check the overflow electrical outlet as well as the normal electrical outlet for leaks.
Ultimately, deal with the bathroom paneling as explained in the producer's user's manual. Tiling and also sealing around the bathtub should wait until the bath tub has actually been utilized at least once as this will certainly resolve it into its last setting.
Planning for the Installment
To start with, the supporting structure provided with the bathroom should be fitted (if required) according to the producer's instructions. Next, fit the faucets or mixer to the bathtub. When fitting the faucet block, it is essential to make certain that if the tap includes a plastic washing machine, it is fitted between the bathroom and the taps. On a plastic bath, it is also practical to fit a supporting plate under the faucets system to stop strain on the tub.
Fit the adaptable tap ports to the bottom of both taps making use of 2 nuts as well as olives (sometimes supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the outlet with the hole in the bath. Make use of the nut supplied by the maker to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the flexible overflow pipeline to the overflow outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bathroom. Make certain you use every one of the supplied washers.
Link the catch to the bottom of the waste outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Connect all-time low of the overflow tube in a comparable manner.The bath need to now be ready to be suited its last position.
Tiling Around the Bathtub
In the area where the bath satisfies the floor tile, it is needed to seal the joins with a silicone rubber caulking. This is important as the fitting can relocate enough to fracture a stiff seal, triggering the water to permeate the wall in between the bath as well as the tiling, bring about problems with wetness and also feasible leaks to the ceiling listed below.
You can pick from a range of coloured sealants to blend in your fixtures and installations. They are sold in tubes and cartridges, as well as can sealing gaps approximately a size of 3mm (1/8 inch). If you have a bigger gap to fill up, you can load it with twists of soaked newspaper or soft rope. Bear in mind to constantly fill the bathtub with water prior to securing, to allow for the movement experienced when the bathtub remains in usage. The sealer can crack rather very early if you do not take into consideration this motion before sealing.
Alternatively, ceramic coving or quadrant ceramic tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are additionally conveniently offered on the market. It is advisable to fit the floor tiles using water-resistant or water resistant adhesive and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I'm very interested by How to Install a Bathtub and I hope you liked the entire page. Do you know about anybody else who is sincerely interested in the topic? Why not promote it. Thanks a bunch for your time. Come back soon.
Access certified emergency plumbing excellence. Report this page